ATV312HD15M3

Altivar 312

Variable speed drive

Asynchronous motors

Simple machine

With heat sink

ATV312

15 kW

20 hp

200…240 V – 15…10 %

50…60 Hz – 5…5 %

3 phases

82.1 A at 200 V, Isc = 22 kA
71.9 A at 240 V

Without EMC filter

28.5 kVA

99 A for 60 s

628 W at nominal load

1…50

Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1…LI6 terminal 2.5 mm² AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 25 mm² AWG 3

Internal supply for logic inputs: 19…30 V 100 mA, protection type: overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm): 10…10.8 V 10 mA, protection type: overload and short-circuit protection

Modbus
CANopen

IP20 on upper part without cover plate
IP21 on connection terminals
IP31 on upper part
IP41 on upper part

Communication card for CANopen daisy chain
Communication card for DeviceNet
Communication card for Fipio
Communication card for Modbus TCP
Communication card for Profibus DP

170…264 V

47.5…63 Hz

22 kA

66 A at 4 kHz

0…500 kHz

4 kHz

2…16 kHz adjustable

170…200 % of nominal motor torque

150 % during 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor

Frequency PI regulator

Suppressable
Automatic whatever the load
Adjustable

<= power supply voltage

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1…LI6: 0.6 N.m
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 4.5 N.m

Electrical between power and control

3

AI1 configurable voltage 0…10 V, input voltage 30 V max, impedance: 30000 Ohm
AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm
AI3 configurable current 0…20 mA, impedance: 250 Ohm

AI1, AI2, AI3: 8 ms analog
LI1…LI6: 4 ms discrete

AOV, AOC 8 ms for analog
R1A, R1B, R1C, R2A, R2B 8 ms for discrete

+/- 0.2 % for output

1

AOC configurable current: 0…20 mA, impedance: 800 Ohm, resolution: 8 bits
AOV configurable voltage: 0…10 V, impedance: 470 Ohm, resolution: 8 bits

Logic input not wired (LI1…LI4), < 13 V (state 1)
Negative logic (source) (LI1…LI6), > 19 V (state 0)
Positive logic (source) (LI1…LI6), < 5 V (state 0), > 11 V (state 1)

2

Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC – 100000 cycles
Configurable relay logic: (R2A, R2B) NC – 100000 cycles

R1-R2 10 mA at 5 V DC

R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms
R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms
R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms
R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms

6

(LI1…LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm

S, U or customized
Linear adjustable separately from 0.1 to 999.9 s

By DC injection

Input phase breaks: drive
Line supply overvoltage and undervoltage safety circuits: drive
Line supply phase loss safety function, for three phases supply: drive
Motor phase breaks: drive
Overcurrent between output phases and earth (on power up only): drive
Overheating protection: drive
Short-circuit between motor phases: drive
Thermal protection: motor

>= 500 mOhm 500 V DC for 1 minute

1 LED (red)drive voltage:
Four 7-segment display unitsCANopen bus status:

5 ms for reference change

Analog input: 0.1…100 Hz
Display unit: 0.1 Hz

1 RJ45 for Modbus/CANopen

RS485 multidrop serial link

RTU

10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen
4800, 9600 or 19200 bps for Modbus

1…127 for CANopen
1…247 for Modbus

127 for CANopen
31 for Modbus

CE

Vertical +/- 10 degree

330 x 245 x 190 mm

329.5 mm

245 mm

192 mm

10.5 kg